Safety Considerations

Safety awareness is the most important thing in the studio. Once you know what can hurt you, you can take precautions. There is no reason to be fearful of chemicals, flames or materials. A healthy outlook is to be present, take steps and measures to be safe and free of dangers.

First we want to address vapors and particles:

  • Any sanding, stirring of powders, sifting of enamels, etc should be accompanied with a particulate mask, such as the RZ perforated mask (www.tonyadavidson.com/blog/recommended-products/)

  • If you are using a fluoridated flux, like Handy Flux, you should also be wearing a vapor mask. I use Prips Flux and I have a very good ventilation systems that takes everything from my bench outside. If you do not have this then I recommend the P100 Dust Half Mask Respirator (see link above). I also recommend you read my blog on Ventilation Hacks for Metalsmiths and work towards setting up a better air flow and vent system. We get one set of lungs and healthcare is too expensive to rule out spending money on tools that will prevent these issues.

Fire:

You want to make sure that your test your equipment regularly for leaks and issues. Hoses get cracked and things get bumped. You want to make sure you have a safety drill practiced in case you have to leave your studio. Are you close enough to shut off the valve to the tank or the emergency cut off valve? If you had to drop your torch have you practiced turning it off quickly and where you would set it.

You want to also make sure you have the right fire extinguisher on hand. Did you know there are several different fire extinguishers? You don’t want the one they sell for kitchens which is for a grease fire. Is it near your bench or at the exit, and have you checked to make sure it is still good? Do you change out your smoke alarm batteries every year?

Do you have some Lavender Oil on hand in case you burn yourself? Do you have a basic first aid kit? In that kit make sure you have some super glue and butterfly strips along with bandaids.

Have you maintained your tools so they work as expected?

Your eyes:

You should wear safety glasses anytime you are working. I have my bench glasses and my magnifiers so they are covered but if I am using the press of something with projectiles or splashing, the kind that cover the sides is the best idea. You can get stick on magnifiers which are on my Tonya Recommends page as well. These stick onto any glasses. I use them on my didymium’s too!

SDS sheets:

All chemicals have Safety Data Sheets (SDS) that will give you important information about storage, usage, and first aid requirements. In most cases they can be downloaded from the manufacturer or seller website. Keep them and your equipment manuals in an easily accessible safety binder in the event you need to refer to them. Make sure you familiarize yourself with the individual characteristics of each chemical in your studio so you can safely handle, store, and use it!

I bought two small cabinets from Wayfair and they store all my chemicals outside. During the winter I move them to the outdoor closet next to my studio and I cover the cabinets with bbq covers. This works really well and I’m happy to share images upon request.

*2026 The Art of Affordable Gold: Part 1 On Demand Encore - Limited Time Offer*

Buy nowLearn more

IMPORTANT INFO

  • SHORTCUT to Tonya’s Online Tool & Supply Shop and 💥 HOW TO ORDER
  • SHORTCUT to Tonya’s Recommended Products
  • Picture Tutorial of Navigating All of Your Content
  • Your 📌DISCOUNT📌 Codes
  • How to use the Video Player for Best Results
  • Save this to your files! How to fix tech issues with accessing this group
  • IMP INFO on FMC TOO (Forged Maker Circle Course/Membership)

Class Information

  • 📌 Terms and Conditions - Creative Work & Use Policy
  • 🍎 About The Class
  • 🙋‍♀️ About Tonya
  • 📅 Dates
  • 💻 Prerequisite Skills and Required Technology
  • 🦺 Safety Considerations
  • Student Release Waiver - Due Date Nov 5th10
  • Connect with me on FB - Join the Private Group
  • Video: How to access your FB group
  • Video: How to get notified of posts on your FB group - Don’t miss a thing!
  • How to get the most out of class

Metals and Metallurgy: 1 hour and 12 minutes of video

  • Video: 2025 AAG Metals and Resources4
  • NEW: Tonya’s Temp Hierarchy Recipe Card.pdf
  • Facts About Gold & Silver
  • Hagstoz Part Numbers and info.pdf2
  • SIlver-Copper+Phase+Diagram.pdf
  • Argentium Quick Start.pdf
  • Argentium Fact File - 0317.pdf
  • Argentium 940 Pro Tech Sheet 1219.pdf
  • 2023 Tips for working with 940 Argentium - C Eid
  • Brittania Silver vs 999, 925, 820.pdf
  • Oct 10, 2025 Recycle figure comparisons.pdf
  • Gold Considerations.pdf
  • Annealing - Why and When
  • Depletion Gilding or Enrichment?.pdf
  • Why Depletion Gilding Works over Super Pickle.pdf2
  • What Happens When Steel Enters a Sodium Bisulfate Pickle.pdf
  • Melting Temps of Solder & Metal Recipe Card

Torches, Gas, and Surfaces: 2 hours and 15 min of videos

  • NEW Torch & Gas What’s Best1
  • Video: Torch Time With Tonya Part 2: Single-Fuel Torches1
  • Video: How to use and set up your EZ Orca Torch
  • Video: German Blow Torch Assembly
  • Using the German Blowpipe 2026
  • Video: German Blowpipe Comprehensive
  • Video: How to setup and use a Swiss Torch 2
  • Video: How to Attach Hoses to the Torch
  • Orca Manual.pdf
  • Swiss Torch.pdf
  • Swiss Torch Regulator Settings
  • Little Smith Manual and Regulator Settings
  • What Surface to Use
  • Tips About Torches
  • Torch Review.pdf
  • Quick Notes on Thermal Boards, Charcoal, Graphite.pdf

Misc Materials and Safety

  • A Brief Explanation of Diamond Grading.pdf1
  • Studio Protocol & Safety. High-Heat Materials.pdf

Facebook Posts of Note

  • FB Post 10.1 on Solder Materials.pdf
  • FB Post 10.1 German Blowtorch
  • FB Post 10.1 Interleaved Practice.pdf
  • FB Post 10.13 What’s in Your Pantry AAG.pdf
  • FB Post 10.17 Bubbles in Casted Metal.pdf
  • FB Post 11.8 Buy Wire or Make It?.pdf

Tools and Materials: 2 hours and 17min of videos

  • Video: 2025 AAG Tools and Supplies
  • Video: Rolling Mill Maintenance and Tips
  • Rolling Mill Comparison.pdf
  • Your Soldering Station
  • Pickling Station
  • How to Make Iron Binding Nests
  • Borax or Boric Acid.pdf
  • Burs - Materials and Cuts.pdf

Resources: 33 min of video

  • Video: Setting Up Your Bench
  • Video: Setting Up Your Efficient Casting Station
  • 2025 AAG Slide Deck Metals, Materials & Tools.pdf
  • Books that you should have in your library!.pdf
  • Ventilation Hacks
  • Setting Up Your Pickle Station & Mixing Pickle.pdf

Session 1: 4 hours of videos

  • Video: Class #1
  • Review for Class #1 AAG Part 1.pdf
  • Video Short: Enriching Sterling Silver
  • What is Bimetal or Doublé.pdf1
  • Video Short: Cutting 1” squares of sterling

Session 2: 4 hours and 7 min of videos

  • Video: Class #21
  • AAG Class #2 Review.pdf
  • AAG 2025 Class #2 Slides.pdf
  • Video Short: Making Rolling Mill Paper Pockets1
  • Costing out Gold - Alloys and Bimetal.pdf
  • Alloy Example Worksheet FS:Cu.pdf
  • Alloy Example Worksheet 18ktF .pdf
  • Alloy Example Worksheet 22kt Ring Shank.pdf

Session 3: 4 hours and 9 min of videos

  • Video: Class #3
  • Class #3 AAG Part 1 2025.pdf
  • Video: Seasoning a Crucible
  • Master Gold Alloy Chart - 1 - Metal Formula Sheets.pdf
  • Karat, Weight & Formula - 2 - Metal Formula Sheets.pdf
  • Cost of Metals Used - 3 - Metal Formula Sheets.pdf

Session 4: 4 hours and 6 min of videos

  • Video: Class #4
  • Class #4 AAG Part 1 2025.pdf
  • 3 things I forgot to show you!
  • Burs - Materials and Cuts.pdf
  • Recipe Card for Cast or Melt

Session 5: 3 hours and 54 min of videos

  • Video: Class #5
  • Class #5 AAG Part 1 2025.pdf
  • Rolling Down Wire.pdf
  • Rolled Wire for Bezels and Frames.pdf
  • 4 - Raise Karat and Raise Fineness - Metal Formula Worksheets.pdf
  • 5 - Prototype From Final Weight - Metal Formula Worksheets.pdf
  • 6 -Silver Alloy Composition Adjustment - Metal Formula Worksheets.pdf
  • Bezel Forming

Bonus: 2 hours of video

  • Bonus Soldering Video